FALL PREVENTION SYSTEM

Lifegear Skylight Protector has been designed specifically to prevent falls through rooflights. The uniquely designed innovative product provides protection for personnel accessing near fragile roof lights while carrying out maintenance or inspections on industrial roofs.

Lifegear vertical components are all made of Stainless Steel and can be installed on various different designs of ladder.

Base Flange

This fitting act as feet to connect raised panel to the roof structure. Material: Malleable cast iron to BS 1562 and galvanised to BSENISO1461.

Single Socket Tee

This fitting is used to connect the horizontal tubing to the vertical tubing at each corner. Material:Malleable cast iron to BS 1562 and galvanised to BSENISO1461.

Single Socket Tee

This Fitting is used to connect the horizontal tubing to the vertical tubing at each corner.
Material:malleable cast iron to Bs 1562 and galvanised to BS EN ISO 1461.

90' Cross Over

Designed to give 90 degree cross joint and reducing the cost by minimizing the pipe cut and increasing the strength. Material:Malleable cast iron to BS 1562 and galvanised to BS EN ISO 1461.

Socket

Designed to form inline joint between two pieces of pipes of same size. Material:Malleable cast iron to BS 1562 and galvanised to BS EN ISO 1461.

Steel Tubes

Standard length supplied O/D 33.20 mm wall thickness 2.6 mm.
Material: Galvanised steel to IS 2629(1985).

Mash Clamp

This single sided Clamp Allow Mesh Panel to be secured to one side of a Vertical bar or horizontal Tube. Suplied with M6x30mm Long Bolt and But Single Clips.

Welding Mesh

Mesh size 25.4 : wire Dia 3 mm
Material: Galvanised steel to IS 4948(2002(.

Pipe End Cap

This component is fitted to the top of the Horizontal Standard Tubing.
Material: PVC

Tape

Water proofing tape.
Available in 40-50 mm width.

Rivit

Rivit of di 6 mm for permanent fixment.
Material: Steel

Self tapping Screw

Self drilling with neoprene washer 5.5 x 55 mm
Material: BZP Steel

Enquiry

CE EN 795:2012 Type C, CEN/TS 16415:2013

Lifegear vertical components are all made of Stainless Steel and can be installed on various different designs of ladder.

Base Flange

This fitting act as feet to connect raised panel to the roof structure.
Material: Malleable cast iron to BS 1562 and galvanised to BSENISO1461.

Single Socket Tee

This fitting is used to connect the horizontal tubing to the vertical tubing at each corner.
Material:Malleable cast iron to BS 1562 and galvanised to BSENISO1461.

Elbow 90d Pipe

The 90 Degree Elbow is Designed to provide A joint between two Two pipes at right angle to each Other. It is Often used as railing end Or corners on a Level installation. Available in Pipe Outlet Size 60 mm to 27 mm.

Cross Over Retrofit Clamp

The Clamping cross over provides a 90 Degree crossover joint to build Railings, Racks and more. although the EF42 Crossover fitting can be used to build Original new Structure.

3 Way open Corner

The 3 Way Open Corner, with its through Hole is Designed as a corner fitting for a middle Rail of handrails, guardrails or Frame. This clamp Fitting available in pipe Outlet size 60 mm to 27 mm.

3 Way Blind Corner

To Be used with a Rubber or Polyamid hose That has an inside diameter as per customer demand. This hollow fitting has an inside flow Hole used for High Pressure Applications. this fitting may come in Zinc or Yellow Zinc Plated Finishes.

Socket

Designed to form inline joint between two pieces of pipes of same size. Material:Malleable cast iron to BS 1562 and galvanised to BS EN ISO 1461.

Steel Tubes

Standard length supplied O/D 33.20 mm wall thickness 2.6 mm.
Material: Galvanised steel to IS 2629(1985).

Mash Clamp

This single sided Clamp Allow Mesh Panel to be secured to one side of a Vertical bar or horizontal Tube. Suplied with M6x30mm Long Bolt and But Single Clips.

Pipe End Cap

This component is fitted to the top of the Horizontal Standard Tubing.
Material: PVC

Tape

Water proofing tape.
Available in 40-50 mm width.

Rivit

Rivit of di 6 mm for permanent fixment.
Material: Steel

Self tapping Screw

Self drilling with neoprene washer 5.5 x 55 mm
Material: BZP Steel

Enquiry
Close Menu
×
×

Basket

ENQUIRY

Facebook Instagram Twitter Link

ENQUIRY

[contact-form-7 id="6409" title="contact Form"]
Facebook Twitter Google-plus Youtube

Item added to your cart

0 items in the cart (₹0.00)

Continue Shopping Go To The Cart